Ruifeng shares operating procedures for asphalt extenders and asphalt ovens

Low-temperature speed asphalt extension tester operating procedures:
1, the machine should be placed horizontally indoors, room temperature 0-25 °C, the relative humidity does not exceed 80%, no vibration, corrosive gas above the ground, has a good grounding protection.
2. Before use, check the depth of the water bath surface to meet the requirements of the test procedure. With all power switches turned off, turn on the power and check the stirring pump. Check whether the pulling power and the moving slide are working well.
3, open the temperature control switch, adjust the temperature control table to a desired temperature, start stirring, according to
4, the test requirements and the ambient temperature need, you can start cooling and heating control.
5, adjust the speed of the front governor to stretch, check the speed of the stretch to the required speed.
6, start stretching, the skateboard back to the left, ready to set the test mode on the skateboard
7. On the metal side of the tank, start the test by stretching. After all the specimens have been broken and broken, stop the power supply of the motor. When the number is broken, the reading is the result of the measurement.
8. When you stop using it, you should first turn off the power switch of each part, and finally cut off the power.
Rotary asphalt film oven operating procedures:
1. Power supply equipment: Overloaded safety devices should be installed in the power supply line for this box, and have a good grounding device, leveling the oven so that the turntable rotates on a horizontal surface. The angle of rotation with the horizontal plane must not exceed 3 degrees.
2, temperature adjustment: Install the thermometer (the thermometer mercury ball bottom about 6 mm from the top of the turntable) adjust the temperature controller to the desired temperature of 163 °C.
3. Close all switches above the switchboard, plug in the power plug, and turn on the power switch.
4, wait until the temperature of the entire studio to rise to the desired temperature (163 °C), you should check the reading of the working thermometer, you can adjust the temperature controller to obtain the correct temperature of the studio, constant temperature for 15 minutes, you can make the asphalt film measurement .
5. Place the sample holder containing the sample on the turntable, turn off the oven, and rotate the turntable. The constant oven temperature is 163°C.
6, in the operation of the box, indoor lighting can not be opened at will, so as not to affect the stability of the studio temperature.
7, after the completion, must cut off each switch.
Shanghai Ruifeng Instrument Manufacturing Co., Ltd. is a company specializing in manufacturing, manufacturing and sales of products. Main products: viscometer, coring machine, constant temperature water tank, impermeability tester, extraction instrument, sand equivalent, hydraulic ejector, extension Instruments, asphalt mixers, ovens, cryogenic water tanks, kinematic viscometers, road viscometers, and Cleveland flash point meters. The company is located in what is known as an international metropolis - Shanghai, Shanghai is China's economy, finance, trade and The shipping center, with China’s largest industrial base, is taking advantage of Shanghai’s geographical advantages, bringing together a large number of high-tech talents, strong technical force, superb manufacturing technology, and the spirit and advantages of continuous pioneering and innovation. It is stepping forward step by step. A little bit of growth. At the same time, it has established close cooperative partnership with many universities and scientific research institutions such as Tongji University, Guangzhou University, Zhejiang University of Technology, and South China University of Technology. It also relies on universities and scientific research institutions to cultivate high-quality technical support and service professionals. , The establishment of professional and technical personnel, research and development of reliable, high-quality products and equipment with the latest domestic instruments and meters to ensure that the company can provide customers with high-quality, high-level professional services. The company has always been focused on product quality, product cost performance, customer requirements, and product innovation, practicality, and convenience. The excellent management concept is well-known throughout the industry. At the same time, good quality, low price, good service and enthusiastic working attitude have won the favor and trust of the new and old customers.

cnc high speed band Sawing Machine 

the H beam size up to 1000 x 500mm with full-automation, mainly for sawing H-beams, channel beams etc, with strong rigidity bridge totally-enclosed sawing device and powerful spindle motor. It can save man-made marking process, so increases production efficiency. It saws steadily, and the sawed section is straight, with good appearance. Also, it is easy to operate, can fully satisfy customers' needs.


CNC DOUBLE COLUMN ANGLE BAND SAWING MACHINE MODEL

1. Sawing section is big with high flatness.
2. High sawing speed and no clip saw in the production.
3. The fine-tuning device at the front and rear of the saw and laser line function.
4. the machine can sawing oblique surface with rotated angle.

Sawing Machine

Sawing Machine,Universal Band Saw Machine,Portable Band Sawing Machine,Woodworking Band Saw Machine

Shandong Sunrise CNC Machine Co., Ltd , https://www.scmcnc.com